16-ch Source-type Digital Output EtherCAT Slice IO Module Channels:16 (Source Type). Voltage Rating:10~30VDC. Rated Current Output:0.5A per channel atsignal "1". Leakage Current:10 μA per channel atsignal "0". Output Delay:From logic level 0 to 1:150μs; From logic level 1 to 0: 2ms.
2-ch Power Input with 4-ch Digital Input EtherCAT Slice IO Module Rated Voltage: 24VDC (± 20%). Dual Power Input: Supported. Max Current on Bus: 2A. Diagnosis Function: Over/under voltage for input 1&2, Over current output on bus..
16-ch Digital Input Modules Input voltage: 30 Vmax. Circuit type: Pull-Up current: 0.5 mA (Source Type). Power consumption: 0.53 W. Channels: 16.
8-ch Source-type Digital Output EtherCAT Slice IO Module Channels: 8 (Source Type). Voltage Rating: 10~30VDC. Rated Current Output: 0.5A per channel at signal "1". Leakage Current: 10 μA per channel at signal "0". Output Delay: From logic level 0 to 1: 150μs; From logic level 1 to 0: 2ms.
EtherCAT Slice IO Extension Function: Conversion of EtherCAT to 100BASE-TX Ethernet for extension of the EtherCAT network. Cable : Ethernet/EtherCAT cable (min. Cat. 5) shielded. Distance between stations : Max. 100 m (100BASE-TX). Bus Interface : 1 x RJ45. Power from bus : N/A.
6-ch Voltage Analog Input EtherCAT Slice IO Module Channels : 6 (Differential). Input Type : V,mV. Voltage Range : ±150 mV, ±500 mV, ±1V, ±5 V, ±10 V. Input Impedance : >10M Ω. Resolution : 16-bit with ±0.1% FSR accuracy. Sample Rate : 100 sample/s (per channel).
8-ch Digital Input EtherCAT Slice IO Module Channels: 8. Digital Input: Dry Contact Logic level 1: close toIso.GND; Logic level 0: open; Wet Contact Rated voltage: 24VDC; Logic level 1: 10~30 VDCand -10~-30 VDC; Logic level 0: -3~3 VDC. Input Delay: From logic level 0 to 1: 4ms; From logic level 1 to 0: 4ms. Digital Filter: 3ms.
8-ch Analog Output Module 8-ch voltage and current output. Range: ±2.5 V, ±5 V, ±10 V, 0~2.5 V, 0~5 V, 0~10 V, 0~20 mA, 4~20 mA. Resolution: 14-bit. Short Circuit Protection. Isolation between channels and backplane.
4-ch Analog Output EtherCAT Slice IO Module Channels: 4. Output Type: V, mV, mA. Output Range: 0~5V, 0~10V, ±5V, ±10V, 4~20mA, 0~20mA. Resolution: 16-bit with accuracy, 0.01% FSR@25°C. Slew Rate: Configurable. Drift: ± 50 ppm/°C. Current Load Resistor: Max. 500 Ω. Voltage Load Resistor: Min. 1KΩ.
16-ch Universal Digital I/O Module Digital input: Support Dry/Wet Contact. Digital output: Open Collector to 30 V, 450 mW max. load. I/O Type: bit-wise selectable by DIP switch. Power consumption: 0.35 W (typical); 1.2 W (max). Channels: 16.
12-ch Relay Output Module Relay type: Form A (SPST). Contact Rating: 5 A @ 250 VAC, 5 A @ 30 VDC. Each digital channel has its own status LED. Isolation between channels and backplane bus.
4/8-ch High/Low Speed Counter Module Supports multiple operating modes: (1) Up mode (2) Up/Down mode (3) Pulse/Direction mode (4) A/B Phase mode (5) Frequency mode. 4 or 8 counter channels depends on operating modes. 32-bit counter range with 1 bit overflow/underflow. 1 MHz counter frequency. 4 digital input channels with counter gate functionality. 4...
24-ch Digital Input Module Supports both sink and source type input. Rated voltage input value: 24 VDC. ±70 VDC over voltage protection. Input characteristic curve according to IEC 61131, type 1. Each digital channel has its own status LED. Isolation between channels and backplane.
12-ch Analog Input Module 12-ch voltage and current input. Range: ±150mV, ±500mV, ±1V, ±5V, ±10V, ±20mA, 0~20mA, 4~20 mA. 2500 VDC over voltage protection. Input characteristic curve according to IEC 61131, type 1. Isolation between channels and backplane.
16-ch Digital Input Modules Input voltage: 30 Vmax. Circuit type: Pull-Up current: 0.5 mA (Source Type). Power consumption: 0.53 W. Channels: 16.
2-ch DO Timestamp Module Precise and Deterministic Digital Output. 2-ch Timestamp Digital Output. Timestamp resolution: 1ns. Synchronized Digital Output.
Intel® Core™ i7/i5/Celeron® Control IPC With EtherCAT Slice IO Expansion 6th generation Intel® Core™ i7/i5/Celeron processors up to 2.6 GHz with 4GB/8GB DDR4 memory. 2 x GbE, 4 x USB 3.0, 2 x RS-232 /422/485, 1 x VGA, 1 x HDMI. Dual power input with alarm output. Compact and fanless design for DIN-rail mount in Control cabinet. Maximum 4 expansion...
Intel® Core™ i7/i5/Celeron® Control IPC With EtherCAT Slice IO Expansion 6th generation Intel® Core™ i7/i5/Celeron processors up to 2.6 GHz with 4GB/8GB DDR4 memory. 2 x GbE, 4 x USB 3.0, 2 x RS-232 /422/485, 1 x VGA, 1 x HDMI. Dual power input with alarm output. Compact and fanless design for DIN-rail mount in Control cabinet. Maximum 4 expansion...
6-ch Thermocouple Input EtherCAT Slice IO Module Channels: 6 differential. Input Type: V, mV, Thermocouple. Input Impedance: >2MΩ. Voltage Range: ±50 mV, ±100 mV, ±500 mV, ±1 V, ±2.5 V. Resolution: 16-bit. FSR accuracy: 16-bit with ±0.1% @25°C. Sample Rage: 100 Sample/Second (per channel).
2-slot Backplane Modules Two slots for two APAX-5000 modules. With built-in expansion ports, two APAX-5002 backplanes can be connected to form a remote expansion. Supports both DIN-rail and wall mounting. Hot swap mechanism for all APAX I/O modules. 30G shock resistance and 2Grms vibration resistance.
4-ch High Speed Analog Input EtherCAT Slice IO Module Channels : 4 (Differential). Input Type : V, mA. Voltage Range : ±10 V, 0 ~ 10 V, 0 ~ 20 mA. Input Impedance : 800 kΩ, for voltage input, 500 Ω, for current input. Resolution : 16-bit with ±0.1% for voltage input, 16-bit ±0.2% for current input. FSR accuracy : @25°C. Sample Rate : 10k sample/s (per...
8-ch Digital Input (2-ch Timestamp & 6-ch without Timestamp) EtherCAT Slice IO Module Precise and Deterministic Digital Input. 2-ch Timestamp Digital Input. 6-ch Regular Digital Input. Timestamp resolution: 1ns. Rising Edge & Falling Edge DI Latch.
12-ch High Speed Analog Input Module 12 analog input channels (12-bit, 1000 sample/second per channel). Supports various input types: 0 ~ 500 mV, ±10 V, 0 ~ 10 V, 0 ~ 20 mA, 4 ~20 mA. Each input channel can be configured with different input types and range. 2500 VDC optical isolation between channels and backplane bus. ±35 VDC over voltage protection....
4-ch RTD Input EtherCAT Slice IO Module RTD Input. Channels : 4. Input Connections : 2 or 3 wire. Resolution : 16 bit with ±0.1% FSR accuracy. Sample Rate: 100 sample/s (per channel). Burn-out detection: Yes.
8-ch Isolated Digital Input Module Digital input level: Logic level 0: +1 V max.. Isolation voltage: 5000 VRMS. Power consumption: 0.27 W (max). Channels: 8.
16-ch Sink-type Digital Output EtherCAT Slice IO Module Channels:16 (Sink Type). Voltage Rating:10~30VDC. Rated Current Output:0.3A per channel atsignal "1". Leakage Current:25 μA per channel atsignal "0". Output Delay:From logic level 0 to 1:10μs;From logic level 1 to 0: 100μs.
20-ch Source Type DO Module Thermal Shutdown Protection. Short Circuit Protection. 2,500 VDC Isolation Between Channels and Backplane.
16-ch Digital Input EtherCAT Slice IO Module Channels:16. Digital Input;Dry Contact;Logic level 1: close to Iso.GND;Logic level 0: open;Wet Contact;Rated voltage: 24VDC;Logic level 1: 10~30 VDC;and -10~-30 VDC;Logic level 0: -3~3 VDC. Input Delay:From logic level 0 to 1: 4ms;From logic level 1 to 0: 4ms. Digital Filter: 3ms.
6-ch Current Analog Input EtherCAT Slice IO Module Channels : 6 (Differential). Input Type : mA. Voltage Range : ±20 mA, 0 ~ 20 mA, 4 ~ 20 mA. Input Impedance : 120 Ω. Resolution : 16-bit. FSR accuracy : 16-bit with ±0.2% @25°C. Sample Rate : 100 sample/s (per channel). Burn-out detection : Yes.
1-ch TTL/RS-422 Incremental Encoder/Counter EtherCAT Slice IO Module Overflow/underflow detection. Latch counter value. Reset counter value. Set counter value. Input filter. Position compare output. Reversion of A/B phase Input. Frequency measurement (Pulse Input).
Intel® Core™ i7/i5/Celeron® Control IPC With EtherCAT Slice IO Expansion 6th generation Intel® Core™ i7/i5/Celeron processors up to 2.6 GHz with 4GB/8GB DDR4 memory. 2 x GbE, 4 x USB 3.0, 2 x RS-232 /422/485, 1 x VGA, 1 x HDMI. Dual power input with alarm output. Compact and fanless design for DIN-rail mount in Control cabinet. Maximum 4 expansion...
2-port Isolated RS-232/422/485 Communication Module Data Bits: 5, 6, 7, 8. Stop Bits: 1, 1.5, 2. Parity: None, even, odd. Baud Rate: 50 bps ~ 230.4 kbps. Data Signals: RS-232: TxD, RxD, GND RS-422: Tx+, Tx-, Rx+, RXRS-485: Data+, Data-. FIFO: 256 bytes. Flow Control: Xon/Xoff.
32 Isolated DI Remote I/O Module for ADAM-5000 Digital Input Channel I/O Type:DI, 24VDC (Sink/Source). Digital Input Channels:32. 2500VDC Isolation voltage protection. Only for ADAM-5560 series.
1-ch SSI Absolute Encoder EtherCAT Slice IO Module Encoder Type: SSI (Binary / Gray code). Latch Counter Value. Comparator *2. Compare trigger Output *2.
PROFINET Communication Coupler 2 x RJ-45 (2-channel switch, share same IP address) Connector. PROFINET Communication Coupler.
12-ch Analog Input Module 12-ch voltage and current input. Range: ±150mV, ±500mV, ±1V, ±5V, ±10V, ±20mA, 0~20mA, 4~20 mA. 2500 VDC over voltage protection. Input characteristic curve according to IEC 61131, type 1. Isolation between channels and backplane.
APAX-5002L, low cost APAX backplane Two slots for two APAX-5000 modules. Supports both DIN-rail and wall mounting. Hot swap mechanism for all APAX I/O modules. 30G shock resistance and 2Grms vibration resistance.
4-Port RS-232/422/485 Communication Modu 4 COM ports for APAX controller. APAX (EtherIO) bus connector. Virtual COM operation mode. COM 1, COM 2: RS-232/422/485. COM 3, COM 4: RS-232/422/485. 8 data bits and 1, 1.5, 2 stop bits. Baud rate 600bps ~ 115.2 kbps. 8KV (air), 4KV (contact) ESD protection. 2,000 VDC (power Line) EFT protection. 2,500 VDC...
24-ch Digital Output Module Voltage Range: 8 ~ 35 VDC. Short circuit protection. Thermal shutdown protection. Each digital channel has its own status LED. Isolation between channels and backplane.
24-ch Digital Input/Output Module 12 DI channels and 12 DO channels. ±70 VDC over voltage protection for DI channels. Short circuit and thermal shutdown protection. Input characteristic curve according to IEC 61131, type 1. Each digital channel has its own status LED. Isolation between channels and backplane.
2-slot Expansion Module with PCIe & I/O 2x full function combo slots (Include 2x High Speed Connector + 2x APAX Connector). Bypass 24VDC to the right side APAX connector for APAX-5002 expansion. EtherIO driver technology to replace the DSP function in the traditional backplane.
2-Port CAN Module 2-ch CAN port. Support CAN2.0B, compatible with CAN2.0A. Data Transfer Rate: 1Mbits/s. Optical isolation protection of 2,500 VDC ensures system reliability.
8-ch RTD Module Wire Burn-out Detection. High Density Channel design, total 8 channels.
12-ch High Speed Analog Input Module 12 analog input channels (12-bit, 1000 sample/second per channel). Supports various input types: 0 ~ 500 mV, ±10 V, 0 ~ 10 V, 0 ~ 20 mA, 4 ~20 mA. Each input channel can be configured with different input types and range. 2500 VDC optical isolation between channels and backplane bus. ±35 VDC over voltage...
12-ch Thermocouple Input Module Isolation between channels and backplane. Supports wire burn-out detection functionality (4 ~ 20 mA and Thermocouple). Range: ±50 mV, ±100 mV, ±500 mV, ±1 V, ±2.5 V, ±20 mA, 0 ~ 20 mA, 4 ~ 20 mA. Supports configurable input channels with different input type and range. High density 12-ch analog input solution for reading...
PC-based Controller w/ Core i3 4th Generation Intel® Core™ i7/i3/Celeron Processors up to 1.7 GHz with 4GB/8GB DDR3L Memory. 2 x GbE, 4 x USB 2.0/3.0, 1 x RS-232 /422/485, 1 x VGA, Audio. Dual power input and UPS support. Compact with Fanless Design. Supports Fieldbus Protocol by iDoor Technology. 3G/GPS/GPRS/Wi-Fi Communication by mPCIe. Chassis...
PC-based Controller w/ Celeron 4th Generation Intel® Core™ i7/i3/Celeron Processors up to 1.7 GHz with 4GB/8GB DDR3L Memory. 2 x GbE, 4 x USB 2.0/3.0, 1 x RS-232 /422/485, 1 x VGA, Audio. Dual power input and UPS support. Compact with Fanless Design. Supports Fieldbus Protocol by iDoor Technology. 3G/GPS/GPRS/Wi-Fi Communication by mPCIe. Chassis...
Modbus/TCP Communication Coupler Support Modbus/TCP protocol which can be connected with Modbus/TCP MDevice. Dynamic configuration allows users to configure multiple inputs functions in one module. Two RJ-45 ports with the same IP address for building daisy chains. Flexible Modbus address mapping either automatically or manually. Able to connect to APAX...
APAX module with iDoor support mini PCI express 2.0 Interface: support Advantech iDoor Technology. mSATA Interface: supportt SATA GENI/GENII/GENIII. Supports Hot Plug.
4-Port RS-232/422/485 Isolation Module 4 COM ports for APAX controller with PCI express interface. COM 1, COM 2 : RS-232/422/485. COM 3, COM 4 : RS-232/422/485. Baud Rate : 50 bps ~ 230.4 kbps. 15 kV ESD protection. 2500 VDC EFT protection. 2500 VDC isolation protection (between COM ports and backplane).
Power Supply for APAX-5570 Series High Power transmission efficiency of over 88% from AC input to DC output. Offer 72 Watt for APAX CPU, coupler and I/O modules. DIN-rail or wall mount installation. Energy Star compliance. UL 508 certification. 4242 VDC Isolation Protection. Output over voltage protection. Over load protection and short circuit protection...
Power Supply for APAX Expansion Modules High Power transmission efficiency of over 88% from AC input to DC output. Offer 72 Watt for APAX CPU, coupler and I/O modules. DIN-rail or wall mount installation. Energy Star compliance. UL 508 certification. 4242 VDC Isolation Protection. Output over voltage protection. Over load protection and short circuit...
8-ch Sink-type Digital Output EtherCAT Slice IO Module Channels: 8 (Sink Type). Voltage Rating: 10~30VDC. Rated Current Output: 0.3A per channel at signal "1". Leakage Current: 25 μA per channel at signal "0". Output Delay: From logic level 0 to 1: 10μs; From logic level 1 to 0: 100μs.
16-ch Sink type DO Module Channels:16 (Sink Type). Voltage Rating:10~30VDC. Rated Current Output:0.3A per channel atsignal "1". Leakage Current:25 μA per channel atsignal "0". Output Delay:From logic level 0 to 1:10μs;From logic level 1 to 0: 100μs.
16-ch Source type DO Module Channels:16 (Source Type). Voltage Rating:10~30VDC. Rated Current Output:0.5A per channel atsignal "1". Leakage Current:10 μA per channel atsignal "0". Output Delay:From logic level 0 to 1:150μs; From logic level 1 to 0: 2ms.
2-ch Counter/Encoder Input Module (32-b Channels: 2. Counting Range: 32-bit. Mode: Counter (up/down, bidirection, up, A/B Phase). Signal Input: Logic level 0: 0 ~ 3 VDC, Logic level 1: 10 ~ 30 VDC. Input Frequency: 5 Hz ~ 1 MHz max. (frequency mode), 1 MHz max. (counter mode).
EtherCAT Slice IO Coupler with ID Switch Function : Coupling EtherCAT IO modules to 100BASETX EtherCAT network. Cable : Ethernet/EtherCAT cable (min. Cat. 5), shielded. Distance between stations : Max. 100 m (100BASETX). Number of configurable IDs : 256 (2 x 16-bit ID switch). Bus Interface : 2 x RJ45 (1 x Input, 1 x Output).
PCIe mini card expansion module Interface: Full size mini PCI express 2.0. SIM card slot: Nano SIM card. Antenna: 1x SMA hole on the top.
2-port GigE Vision Frame Grabber Module Compatibility: IEEE 802.3, IEEE 802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3af. Speed: 10/100/1000 Mbps. No. of Ports: 2 Gigabit Ethernet Media Access Control (MAC) andphysical layer (PHY) ports. Input Voltage: 24 VDC direct from WISE-5000 CPU module.
2-port PoE Vision Frame Grabber Module Compatibility IEEE 802.3, IEEE 802.3u, IEEE802.3ab, IEEE802.3x,IEEE802.3af. Speed: 10/100/1000 Mbps. No. of Ports: 2 Gigabit Ethernet Media Access Control (MAC) andphysical layer (PHY) ports. Input Voltage: 24 VDC direct from WISE-5000 CPU module. Output PoE Power: 48 VDC PoE Power output, 15.4W per port, total...
4x USB 3.0 Module Host Bus 4-lane Gen 2.0 PCIe interface, compliant with PCIExpress Base Specification, Revision 2.0. Controller Host Controller – Fresco FL1100Compliant with USB 3.0 Specification and Intel® xHCI Specification, Revision 1.0. Max. Current: 1500 mA maximum per port. Data Transfer Rate: SuperSpeed (5.0 Gbps); High Speed (480.0 Mbps); Full...
4-slot Edge Intelligent DAQ controller Linux C programming based on Linux operating system. Built-in real-time clock and watchdog timer. 4 serial communication ports onboard. 2 Ethernet Ports. 4 or 8 I/O slot expansion. 1 micro SD slot expansion for data storage.
8-slot Edge Intelligent DAQ controller Linux C programming based on Linux operating system. Built-in real-time clock and watchdog timer. 4 serial communication ports onboard. 2 Ethernet Ports. 4 or 8 I/O slot expansion. 1 micro SD slot expansion for data storage.
16-ch Isolated Digital Input Modules 50 Vmax Input Voltage. 2500 Vdc Optical Isolation. 70 Vdc Over Voltage Protection. 16-channel.
